[filmscanners] Re: Some findings/thoughts on the Sprintscan 120(comments verywelcome please)

["Arthur Entlich" <artistic-1@shaw.ca>]

Hi Simon,

I am pleased you have brought these issues into the public list because
there are people here who have more experience with Insight than I,
especially in terms of how it functions with the SS120.

Further, I had another thought.  It is possible that there are aspects
of the software that work better in the PC environment than the Mac.
Just to make it clear, to avoid any flame war, I am not implying that
the PC is a better platform for scanning, or color management, or
whatever.  What I am suggesting is that perhaps some aspect of the Mac
OS causes differing results with Insight, and that either there are
adjustments that can be made within the Mac operating system or Insight,
which I would not be aware of, which can remedy some of the problems you
are experiencing.

Therefore, the reported experiences which seem so divergent, might be as
a result of different platforms or OS.  Someone who is running an SS120
with Insight on a Mac might be able to provide you with some guidance
which I am unable to if that is the case, since all my experience with
Insight has been under the PC Windows OS platform.

Art


Simon Lamb wrote:

> I have had some private communication with Art Entlich regarding the SS 120
> and he has been, and is continuing to be, very helpful and supportive.  I
> though I would share some of the comments that I made with the group to see
> if anyone has any comments to make.  All would be welcome.
> ____________________
>
> I have scanned quite a few slides so far and have had varying results.  The
> film term in Insight for Kodak Porta 160 is way, way off.  The resulting
> scan bears absolutely no resemblance to the original neg. or even the
> prints, and required so much work in Photoshop to recover it that I gave up,
> it just seemed unrecoverable.  I think the film terms in general within
> Insight need to be reviewed.  Scanning using the generic slide terms when
> using Provia also produced bad results.  The only good scan I got was using
> the generic slide term when scanning Kodak E100VS.  As for black and white,
> after over ten attempts with Scala, Delta 100 and Delta 400 I gave up.  The
> scans where very dark, the black point stopped dead on all scans at about
> 30, as if all the pixels at that end had been pushed up against a wall.
>
> So, I moved on to using Vuescan.  The Provia scanned well although the
> colour accuracy was not too good.  My Nikon Coolscan LS30 produced a better
> scan from a colour perspective, although obviously not as detailed.  The
> Delta 100 scan was one of the best black and white scans I had ever seen.
> Absolutely perfect tonal balance and immense detail.  The Scala was good but
> lost some detail in the highlights.  The Porta 160VC was detailed but there
> was a significant amount of white speckling all over the scan.  I assume
> from this, and the fact that the Insight term produced the worst scan
> imaginable, that the SS 120 just has difficulty with the Portra emulsion.  A
> shame, since my LS30 scans it very well.
>
> So where am I now.  Well, the SS 120  can obviously produce detailed scans,
> but I will have to rely on Ed Hamrick's Vuescan to get them, especially for
> black and white which is a big proportion of my work.  I am not really happy
> about relying on third party software because should Ed decide to pack it in
> then I will have a scanner from which it will be difficult to get the
> results I need.  The carriers are fiddly.  In many cases the 6X6 film does
> not lie perfectly flat in the carrier, and it is impossible to line up a
> strip of 35mm unless you leave the carrier slightly undone.  Most of the
> scans I did using Insight required a lot of work in Photoshop to get them
> close to what I wanted,  and some were just too far out to be workable.
>
> I think I will return the SS 120 and try the Flextight Photo.  I did find
> when comparing it side by side with the SS 120 in the store that the Photo
> just about always reproduced the image as near as possible to the original
> colour, contrast etc.  The built in film profiles seemed to be accurate.  It
> may take twice as long to scan, but I may save that additional time not
> having to do so much in Photoshop.
>
> Your comments on my findings would be welcomed.  I know a lot of people use
> the SS 120, so either I am doing something wrong or they just put the effort
> in to correct images post scanning.
>
> I was using Insight 5.5.1.
>
> Regards.
>
> Simon
>


----------------------------------------------------------------------------------------
Unsubscribe by mail to listserver@halftone.co.uk, with 'unsubscribe 
filmscanners'
or 'unsubscribe filmscanners_digest' (as appropriate) in the message title or 
body